ปกบทความ พิมพ์ DTG แล้วขนผ้าแทงทะลุหมึก แก้ได้ด้วย 3 ข้อ

DTG print looks fuzzy with fibres poking through: 3 things every new DTG owner must know

Short answer: Fibres poking through a DTG print come from how the shirt is handled after pretreatment. Fix it with 3 habits: press light at 175–180°C for 50–60 seconds with the lowest pressure, the Teflon sheet must not stick (it should lift off by itself, no pulling), and do not touch the print area (move the shirt by its corners).

Your DTG print comes out fuzzy, with tiny fibres poking up through the ink. This is one of the most common problems for shops with their first DTG printer, and it usually has nothing to do with the printer or the ink. It comes from pressing the pretreatment and handling the shirt before printing. Watch SK's short video (Thai), then read the 3 steps below.

🎬 Video summary (Thai) · 82 seconds

What fibres poking through look like

Cross-section of a DTG print: fibres poking through the white ink make it fuzzy; fibres lying flat under the ink give a smooth print

Cotton has tiny fibres on its surface. When they lie flat, the white ink covers the shirt smoothly. When they stand up before printing, they poke through the ink layer and the print looks fuzzy. It shows most on dark shirts.

Fibres get lifted at 3 moments: while pressing, when the Teflon sheet comes off, and when hands touch the shirt. So there are 3 fixes.

Step 1: press light (hot enough, long enough, but gentle)

Pretreatment press settings: 175 to 180 C, 50 to 60 seconds, lowest pressure; pneumatic press 1 to 1.5 bar; lever press close gently
  • 175–180°C
  • 50–60 seconds, or until the pretreatment is dry
  • Lowest pressure possible: steam escapes easily, the pretreatment dries faster, and there are fewer pretreatment stains
  • Pneumatic heat press: set 1–1.5 bar
  • Manual lever press: close it gently, no force

These values sit inside the default range on the SK pretreatment product pages (heat press 165–180°C for 40–60 s).

Step 2: the Teflon sheet must not stick to the shirt

Teflon sheet stuck to the shirt pulls fibres up, compared with a sheet that lifts off by itself

When you open the press, the Teflon sheet should come away from the shirt by itself, with no pulling or peeling. Then the fibres are not pulled up.

If the Teflon sheet sticks: wipe it with alcohol and a polyester cloth, press again 5 to 10 seconds, check again

If the sheet sticks:

  1. Wipe the Teflon sheet with alcohol and a polyester cloth
  2. Press again for 5–10 seconds
  3. Check again: the sheet must lift off by itself

Step 3: load the shirt without touching the print area

A hand on the print area makes fibres stand up; pulling the shirt by its corners keeps them flat

When you put the shirt on the platen, do not touch the area you will print. If you need to straighten it, pull it by the corners. Touching makes the flattened fibres stand up again.

Small trick: mark the side that touches the shirt

Star mark on the shirt side of the Teflon sheet keeps dirt from the heat press off the shirt

Mark one side of the Teflon sheet as the shirt side and always put that side down. Dirt from the heat press then stays off the shirt, which helps a lot if the press is shared with other print jobs.

Easy to remember

Summary: press light, Teflon sheet does not stick, do not touch the print
  1. Press light: 175–180°C · 50–60 s · lowest pressure
  2. Sheet does not stick: lifts off by itself
  3. Do not touch the print: move the shirt by its corners

SK pretreatment

SK DTG pretreatment is made in Thailand in versions for each fabric and shirt colour: PRT-DTG-DC for dark cotton, PRT-DTG-UDC premium, PRT-DTG-WC for white and light shirts. See all at SK Pretreatment.

Still seeing fibres? Send a photo of the print to the SK team.

LINE @skcolor

Written by the SK Color & Chemicals team from SK's own training video and SK pretreatment product pages · Updated Nov 2026
All drawings are simplified illustrations.

Previous article Brother GTXpro และ GTX pro B: เจออาการไหน อ่านคู่มือหน้าไหน รวมคู่มือ SK Fix Center ทุกหน้าไว้ที่เดียว
Next article โปรแกรม RIIN (เครื่อง DTG / DTF จีนหัว i3200): เจออาการไหน เปิดเมนูไหน รวมคู่มือ SK Fix Center ทุกหน้าไว้ที่เดียว